Quality Window Brands that Matter |
Which is Best for Me?
(Essential - Elevate)
Integrity windows and doors are made with Ultrex®, a pultruded fiberglass they’ve patented that outperforms and outlasts vinyl, roll-form aluminum and other fiberglass composites. Using Ultrex and their proprietary pultrusion process to manufacture high-demand windows and doors that endure all elements without showing age or wear. |
(Marvin Signature)
Known to challenge industry standards, Marvin strives to push design to its limits in aesthetics, function and durability. Their products are preferred for new construction, remodels and replacement projects when compromise isn’t an option. |
Family owned and managed since its establishment more than half a century ago, the Semling-Menke Company operates under a single guiding philosophy: Produce the best quality windows and doors possible.
|
Compare Our Window Products
We can install any of the brands below, but we prefer Integrity, Marvin and SEMCO. The chart below shows why.
* A caveat regarding Limited Lifetime Warranties: Typical for most vinyl window manufacturers is the "Natural Weathering of Exterior Finish" warranty exclusion. In the Southwest region with high ultra violet exposure, high temperatures and extreme temperature swings, this type of warranty exclusion virtually eliminates coverage for warping, discoloration, cracking, crazing or degradation to the vinyl frame and sash components.
|
Our Proven Installation Process
Introduction
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Step 8
Step 9
Step 10
Introduction
IntroductionA superior seal to the building is facilitated when replacement windows are installed with an integral factory nail fin, the same as is required for a new construction installation. The aesthetics are also greatly enhanced, considering the stucco will abut directly to the new window frame and supersede the need for trim pieces that have been systematically utilized for replacement windows in the past. A nail fin installation for replacement windows is very similar to the methods utilized for a new construction installation, and one that is adopted and regulated by many State, County and Municipal Building Departments for replacement window installations. In New Mexico, Bernalillo County, Los Alamos County, the City of Rio Rancho and the City of Albuquerque all require the nail fin installation method for replacement windows in stucco homes. For the installation into a stucco finish, our windows are ordered with an integral nailing fin, which is an attached flat projection that runs perpendicular the perimeter of the window frame (like a dorsal fin to a fish), and lays flat against the building sheathing (OSB or Plywood). This nailing fin allows sealant and flashings to be transitioned from the existing paper vapor barrier to the new replacement window, for a complete weather-tight, waterproof, air barrier. The application of the stucco system then provides additional weather resistant protection, but it is the nail fin and flashings that create the ultimate weather proof seal, when properly integrated to the existing building envelope.
|
Step 1
Step 2
Step 3
Step 4
Step 5
Step 5
Caulking is applied to the backside of the nailing fin at the sides and top and then the new window installed into the opening. The window is leveled, plumbed, trued up, and secured with screws through the nail fin to the existing framing, providing a reliable attachment and weatherproof interface to the building.
Step 6
Step 6
Protecto Wrap window flashing adheres to the nailing fin and over the existing building paper at the sides, and under the existing building paper at the top. This flashing application method is commonly referred to as the “shingle effect” and is the same water management method employed for shingle roofs, allowing the moisture to cascade downward from the top to bottom without entering the building envelope.
At this point of the installation, your new windows / doors are completely secured and sealed to your home, providing the ultimate protection against the weather elements. This work is accomplished by our highly trained window technicians, who are hourly employees and have undergone rigorous training for the Reule Smart Seal installation system. Once your windows are property installed with the Reule Smart Seal system, the stucco at the peri meter of the windows will require patching prior to the finish coats.
|
Step 7
Step 8
Step 9
Step 10
|
Considering Stucco as Well?
Get our exclusive Total Coordinated Installation
Call (505) 345-3200
for a Free Estimate
(Or click here.)
ONE CALL DOES IT ALL • HASSLE FREE • NO PRESSURE